153032120

Slim design with high coding level!

The AZM150 is an electromechanical solenoid interlock in a slim design. The slim housing was designed to match the aluminum profiles used in many machine guard doors. The rotatable head is locked in place by the front cover and offers some mounting flexibility. The solenoid lock provides 1500 N force to secure the machine guard where access to a hazardous work area must be controlled until safe conditions exist.

The AZM150 is also available with individual coding, for enhanced tamper resistance. Schmersal is the only manufacturer which offers electromechanical solenoid interlocks with "high" coding levels to ISO14119.

The AZM150 is an electromechanical solenoid interlock in a slim design. The slim housing is just 40 x 48 x 204 mm and was designed to match the aluminum profiles used in many machine guard doors.

Solenoid interlocks are designed for machine/work cells where access to a hazardous work area must be controlled until safe conditions exist. The AZM150 solenoid provides a 1500 N locking force to secure the machine guard until dangerous conditions, which may exist immediately after removal of power, have abated. The solenoid lock may be controlled by a time delay, motion detector, position sensor or other suitable component. Additionally, there is a 50 N latching force, keeping the guard door closed, even when not locked.

The solenoid is electromagnetically controlled, with power-to-lock and power-to-unlock versions. Power to unlock versions are available with a manual release, emergency release (N), or emergency exit (T).

The AZM150 offers mounting flexibility, the head of the switch offers two actuator key entries (top and side) and can be rotated in 90-degree steps. The same switch can be used for left or right facing doors. The front cover locks the head in place, so rotation of the head can occur when installing wiring.

There are three standard actuator keys: The B1 standard key is flat, the B5 has a right angle for mounting. The B6 has a flexible mounting block, to accommodate actuator movement for small radius doors. A door handle system is planned. Actuator keys are ordered separately.

This series is also available with individually coded versions to deter the bypassing of locking mechanisms. The AZM150i uses 5 separate cams, to offer over 1000 possible combinations. This is coding level high; to ISO 14119. The uniquely matching actuator is supplied with the switch, as standard actuators will not work. Schmersal is the only manufacturer which offers electromechanical solenoid interlocks with high coding levels.

Features Include:

• Thermoplastic enclosure
• Eight approach levels thanks to rotating head
• Individually coded version with coding level "High" according to
• ISO 14119
• Simple fitting, especially on 40 mm profiles
• Mechanical life, minimum: 1,000,000 Operations
• Clamping force (in accordance with ISO14119 Fzh): 1,500 N
• Clamping force, maximum Fmax: 1,950 N
• Latching force, approx.: 50 N
• Mounting: Screws
• Terminal Connector: Screw terminals
• Cable entry: 3 x M20 x 1,5
• Cable section, minimum: 1 x 0.25 mm²
• Cable section, maximum: 1 x 2.5 mm²
• Length of sensor: 48 mm
• Width of sensor: 40 mm
• Height of sensor: 204 mm
• Thermal test current: 5 A
• Rated control voltage: 24 VDC
• Required rated short-circuit current to EN 60947-5-1: 400 A
• Electrical power consumption, maximum: 8.5 W

Technical Information:

• Schmersal AZM150SK-02/02R-024 Solenoid Interlock Datasheet
• Schmersal AZM 150 Solenoid Interlock Brochure
• Schmersal AZM 150 Solenoid Interlock Operating Instructions
• Schmersal MP-AZM150xxx Supplementary Sheet Mounting Plate Operating Instructions
• Schmersal Electronic Safety Sensors and Solenoid Interlocks Catalog